Lenze DSD User Manual Page 481
- Page / 496
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23 481
18 Drive dimensioning messages
18.12 Brake resistor
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
18.12 Brake resistor
18.12.1 Resulting brake resistance too low
18.12.2 Permanent utilisation of the equivalent resistance > 100 %
18.12.3 Max. utilisation of the equivalent resistance is >100 %
Warning!
The resulting equivalent resistance is xxx Ohm. Thus the value falls below the minimum permissible brake
resistance on the brake transistor of yyy Ohm.
Cause Effects Possible remedies
The value falls below the minimum
permissible resistance.
The brake chopper or brake module is
overloaded.
• Use different resistor.
• Select different resistor intercon-
nection.
• Increase number of brake chop-
pers/brake modules.
Brake resistor selection
( 368)
Warning!
The permanent utilisation of the equivalent resistance is xxx %.
Thus the limit value of 100 % is exceeded.
Cause Effects Possible remedies
The resistor is overloaded with re-
gard to the peak braking power.
The inverter indicates overvoltage.
Drive moves in an uncontrolled way!
• Use different resistor.
• Use different resistor intercon-
nection (series connection).
Brake resistor selection
( 368)
Warning!
The max. utilisation of the equivalent resistance is xxx %.
Thus the limit value of 100 % is exceeded.
Cause Effects Possible remedies
The required peak braking power is
too high.
The brake resistor is overheated.
Fire hazard!
• Select longer braking times.
• Use resistor with higher peak
braking power.
• Connect several brake resistor so
that a higher peak braking power
is possible.
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Related products and manuals for Software Lenze DSD
Software Lenze Engineer v2.21 User Manual
(312 pages)
(312 pages)
(270 pages)
Software Lenze 8400 motec User Manual
(518 pages)
(518 pages)
Software Lenze i700 User Manual
(338 pages)
(338 pages)
Software Lenze 8400 TopLine User Manual
(176 pages)
(176 pages)
Software Lenze 8400 StateLine User Manual
(103 pages)
(103 pages)
Software Lenze 8400 HighLine User Manual
(157 pages)
(157 pages)
Software Lenze 8400 BaseLine C User Manual
(342 pages)
(342 pages)
Software Lenze 8400 BaseLine D User Manual
(260 pages)
(260 pages)
© 2020, manymanuals.com. All rights reserved. | 0.713 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals