Lenze DSD User Manual Page 442
- Page / 496
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
18 Drive dimensioning messages
18.1 Applications
442
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
18.1.4 Speed of the application = 0 (standstill)
18.1.5 Safety check of controller inhibit failed
18.1.6 No values available for the torque of the application
Stop!
The speed of the application is xxx min
-1
.
With this value, dimensioning is not possible.
Cause Effects Possible remedies
The velocity or speed entered is 0.
This is not a valid operating status for
the dimensioning.
This leads to subsequent conflicts if a
motor with a gearbox is selected, be-
cause the calculation of the trans-
mission ratio will involve a division
by zero.
If a motor without a gearbox is used
it is possible to continue, since only
the holding moment has to be de-
rived.
Enter a non-zero velocity value speed
value.
Warning!
Controller inhibit was activated although a torque from the drive is available.
Cause Effects Possible remedies
Brake has not been activated. • Drive is unguided with inhibited
controller.
• Drive moves in an uncontrolled
way.
Deactivate controller inhibit, or acti-
vate brake.
Stop!
The data imported or entered do not contain any values for the torque!
Without values, dimensioning is not possible.
Cause Effects Possible remedies
The application does not generate
any torque. If no torques or forces are
specified or imported and no frictions
or accelerations are specified for
masses or mass inertias, the calcula-
tion of the application torque results
in 0 Nm.
For this drive dimensioning, the DSD
needs the corresponding process pa-
rameters. Dimensioning without
these parameters is not possible.
Check entered values or imported
motion profile.
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Related products and manuals for Software Lenze DSD
Software Lenze Engineer v2.21 User Manual
(312 pages)
(312 pages)
(270 pages)
Software Lenze 8400 motec User Manual
(518 pages)
(518 pages)
Software Lenze i700 User Manual
(338 pages)
(338 pages)
Software Lenze 8400 TopLine User Manual
(176 pages)
(176 pages)
Software Lenze 8400 StateLine User Manual
(103 pages)
(103 pages)
Software Lenze 8400 HighLine User Manual
(157 pages)
(157 pages)
Software Lenze 8400 BaseLine C User Manual
(342 pages)
(342 pages)
Software Lenze 8400 BaseLine D User Manual
(260 pages)
(260 pages)
© 2020, manymanuals.com. All rights reserved. | 2.512 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals