Lenze DSD User Manual Page 353
- Page / 496
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23 353
11 Drive Dimensioning
11.6 Inverters
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
11.6.2 Preselection
In the following subchapters the parameters for the preselection of the inverter are described.
11.6.2.1 Motor output
11.6.2.2 Design
11.6.2.3 Switching frequency
According to the inverter, different settings of the switching frequency can be carried out. The
switching frequency can be selected between "variable" or "fixed".
• If a variable switching frequency is used, the respective maximum available switching frequen-
cy is specified. However, this switching frequency is not reached if the inverter is subjected to
higher loads.
• Depending on the modulation mode of the switching frequency, a power-optimised or loss-op-
timised operation of the inverter can be carried out.
Symbol Description
• Single axis
•Double axis
Symbol Description
•BaseLine
• StateLine
•HighLine
•TopLine
Symbol Description
f
ch,set
Switching frequency of the inverter
• At higher switching frequencies, acoustic motor noises and controller output currents are re-
duced. With a decreasing switching frequency, however, the losses in the motor increase.
• The preselection in the DSD corresponds to the Lenze setting of the inverter selected.
• Select the switching frequency at which the inverter is to be actuated.
• According to the selection, the respective rated data is displayed in the selection table.
• If the drive is to be actuated with a variable switching frequency, the max. possible output
current can only be reached with the lowest switching frequency.
• For inverters with a variable switching frequency in the Lenze setting, the lowest switching
frequency is to be selected.
Note!
Derating for the motor
• If the selected switching frequency is too low for the motor, a derating must be carried
out.
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Related products and manuals for Software Lenze DSD
Software Lenze Engineer v2.21 User Manual
(312 pages)
(312 pages)
(270 pages)
Software Lenze 8400 motec User Manual
(518 pages)
(518 pages)
Software Lenze i700 User Manual
(338 pages)
(338 pages)
Software Lenze 8400 TopLine User Manual
(176 pages)
(176 pages)
Software Lenze 8400 StateLine User Manual
(103 pages)
(103 pages)
Software Lenze 8400 HighLine User Manual
(157 pages)
(157 pages)
Software Lenze 8400 BaseLine C User Manual
(342 pages)
(342 pages)
Software Lenze 8400 BaseLine D User Manual
(260 pages)
(260 pages)
© 2020, manymanuals.com. All rights reserved. | 2.350 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals